Showing 1036–1044 of 1291 results
-
Resuscitation Unit (STANDARD)
Technical Specification
- Microprocessor controlled unit allow three operational mode, Pre-warm, Manual or Automatic (Servo Controlled temperature System).
- Audio and Visual alarm function for Power failure, temperature deviation, over temperature & Temperature sensor failure.
- APGAR timer to record therapy time
- Convenient X-ray cassette tray under infant mattress.
- Effective carbon steel heater, Specially designed heater head for convenient X-ray test
- Separate display of set & skin temperature
- Inclination of infant bed is adjustable.
- LED Observe light angle is adjustable
- Foldable transparent side panels with two infusion seals.
- Temperature deviation can be amended in front panel directly
- Low pressure suction unit, oxygen supply system and LED phototherapy unit
- Electric height adjusted suit for operation
-
Resuscitation Unit with Fixed Baby Cradle & Drawers with Microprocessor based temperature controller with 4 modes Skin/Air/Manual/Prewarm Mode
Mechanical Specifications :
- Fixed height warmer with attached baby cradle mounted on 4″ wheel
- Stainless steel baby tray with water proof, zipped cover mattress of density approx. 21-25 kg/m³
- Continuous head up/down facility
- X-Ray cassette holder
- Collapsible/lockable Side Supports made up of Unbreakable polycarbonate material
- Slots for sensor and ventilator tubing
- Side tray for placement of monitor
- Stainless steel infusion rod with facility to mount Syringe/infusion pump
- Lower shelf below baby tray to facilitate under surface phototherapy. Three drawer for storage.
- Integrated support for 10L Oxygen bottle.
- Oxygen regulator with pressure gauge, flow meter and humidifier bottle along with silicon tubing for delivery of oxygen from humidifier bottle to patient.
- Integrated electrical operated Slow Suction unit with Vacuum Regulator, Vacuum Gauge and autoclavable fluid jar.
- Silicone manual Resuscitator for Infant (250ml) along with face masks size 00 and 01.
- Laryngoscope – Penlight handle with straight blade size 0 and 1.
- Silicone Airways – size 000, 00, and 0
- Height : 74.5″ (1890 mm), Width : 28.0″ (710 mm), Length : 39.0″ (990 mm)
- Bed to Floor Height : 37.5″ (950 mm)
- Distance between baby bed and heater: 33″ (840 mm)
- Mattress size: 30″ (762 mm) x 20″ (508 mm)
- Height of side panel above baby bed: 5.75″ (145 mm)
- Microprocessor based temperature controller with Pre-warm, Manual and Skin Servo modes
- LED Display of Skin Temp., Air Temp., Set Temp. (Resolution 0.1°C) & Heater Power %.
- LCD to display modes of operation, Alarm messages, Skin Temperature in °F and Timer.
- Thermistor based sensor with Accuracy of +/- 0.2°C (Temp. Calibration not require)
- Modes of Operation: Skin Servo, Air, Manual and Pre-Warm
- Keypad lock facility
- Skin mode: Temperature range: 34 to 38°C , Resolution : 0.1°C
- Air mode: Temperature range: Room temp. to 39°C , Resolution : 0.1°C
- Manual mode: Adjustable Heater Power 0 to 100% (with an increment of 5%), Time duration:15mins
- Pre-warm mode: To pre-warm the cradle before baby is placed on the bed. (No alarm will be activated during Prewarm mode) Adjustable Heater Power 0 to 25% (with an increment of 5%), Time duration:30mins
- Overhead heater box: Swivelling, Consists of Ceramic heater (650 Watts) placed in parabolic reflector with a safety grill & Halogen observation light (12V/50W) for observing the baby
- Operating Voltage: 220-240 VAC, 50Hz
- Power: 800W (Max.)
- Alarm: Audio alarm with 10 minute mute facility & Visual alarms with message on LCD
- Power Fail Alarm: Audio with LED indicator
Dimensions :
Performance/Electrical Specifications :
-
Retort Stand
Retort Stands provide excellent replacement for the metal ones. Even the metallic rod has a polypropylene covering making it non-corrosive. The rod measuring 12.5 mm x 750 mm can be screwed into the heavy base giving way to perfectly stable Retort stand.
Particulars Pack(Pcs) Pack (Pcs) Retort Stand 225 x 150 mm – Side Hole 1 Retort Stand 300 x 200 mm – Centre Hole 1 Retort Stand 300 x 200 mm – Side Hole 1 -
Revolving Stool
Four legs, stainless steel top. Wholly stainless steel frame
- Heigh : Adj. 46/68cm.
- Top dia : 35cm.
-
Ria Vial
These Polypropylene/Polystytene tubes are generally used in RIA, Coagulation & Bacteriology. The Polypropylene tubes are clear and can withstand 3000 RCF during Centrifugation while the transparent Polystyrene tubes can withstand 1400 RCF. The PP tubes can accept common acids, alkalis & solvents at room temperature while the PS tubes can accept mild bases, weak acids but not organic solvents.
Particulars Size Pack (Pcs) RIA Vail 12 x 75 mm / PS 500 RIA Vail 12 x 75 mm / PP 500 Cap For 12 mm RIA Tube 100 -
Ring Launcher
Ring Launcher
Specificatons :
The ring launcher consists of a vertically mounted solenoid of thick copper wire with an iron core. The coil is energized with by pressing the push button on the panel. Two aluminum rings are supplied with the apparatus. These rings fit over the solenoid and are supported at some height above the base by an adjustable collar. The behaviour of the rings when the coil is energized depends on the type of the ring placed over the coil at the time. The solid aluminum ring is propelled straight up while the slotted ring remains static, thus demonstrating the principle of electromagnetic induction as well as Lenz law.For similar products visit at main page of Magnetism Physics Labware.
-
Ring Magnet Ceramic
Details for Ring Magnet Ceramic for Physics Lab
An annular magnet with face poles..
Internal dia 12.5 mm, External dia 30 mm, thickness 6.5 mm.We are leading manufacturers, suppliers & exporters of Ring Magnet Ceramic for Physics Lab. Contact us to get high quality designed Ring Magnet Ceramic for Physics Lab for schools, colleges, universities, research labs, laboratories and various industries. We accept bulk orders for government tenders in all countries around the globe.
For similar products visit at main page of Magnetism Physics Labware.
-
Ripple Tank (Dual Purpose) For Physics Lab
Details for Ripple Tank (Dual Purpose) for Physics Lab
The apparatus consists of a framed tray with a plexi glass base and detachable legs, overall size of tray 600 x 520 x 56 mm deep. A pair of support rods with integral ‘G’ clamps is provided which can be attached to the sides of the tank and used to carry the wave generating system. A set of 4 metal barriers (reflectors) is included consisting of a pair of straight barriers 150 x 25 mm, a curved barrier of 215mm chord length x 25mm high and a short, straight barrier of 25 x 25 mm. To minimize unwanted reflections from the sides of the tank a set of four loose gauze strips are provided which when in use are arranged around the edges to from a ‘beach’ on all sides. The ripples are produced by a small 1.5 to 4.5V D.C. electric motor mounted at the centre of a waxed wooden wave generator bar with a row of holes to mount the spherical dipper supplied. It is recommended that the power supply unit is used as this has been specially designed for use with the ripple tank. It has continuously variable D.C. Output so that the speed of the motor and hence the frequency of the ripples may be varied. One white card sheet may be placed on the floor underneath the tank as a screen to receive the wave pattern shadows.
Tank can be used with an overhead projector.The full set of apparatus comprises:
· Ripple tank 300x300x35mm deep
· Gantry complete with beam 4.5V DC motor fittings
· Screw in legs for bench mounting.
· Illuminant support rod.
· Spherical dippers
· Glass plate and spacers for refraction
· Dropper
· Suspension bands
· Leveling wedgesWe are leading manufacturers, suppliers & exporters of Ripple Tank (Dual Purpose) for Physics Lab. Contact us to get high quality designed Ripple Tank (Dual Purpose) for Physics Lab for schools, colleges, universities, research labs, laboratories and various industries. We accept bulk orders for government tenders in all countries around the globe.
For similar products visit at main page of Physics Sound & Waves Lab.