Infant Radiant Warmer with Fixed Baby Cradle and Drawers with Microprocessor based temperature controller with 4 modes Skin / Air / Manual / Prewarm mode
0.00
Standard Specifications
- Fixed height warmer with attached baby cradle and drawers mounted on 4″ (100mm) wheels, 2 with brake.
- Stainless steel baby tray with water proof, zipped cover mattress of density approx.21-25 kg/m³
- Continuous head up/down facility
- X-Ray cassette holder
- Collapsible/lockable Side Supports made up of Unbreakable polycarbonate material
- Slots for sensor and ventilator tubing
- Side tray for placement of monitor
- Stainless steel infusion rod with facility to mount Syringe/infusion pump
- Lower shelf below baby tray to facilitate under surface phototherapy, Facility of 3 drawers for storage
- Height : 74.5″ (1890 mm), Width : 28.0″ (710 mm), Length : 39.0″ (990 mm)
- Bed to Floor Height : 37.5″ (950 mm)
- Distance between baby bed and heater: 33″ (840 mm)
- Mattress size: 30″ (762 mm) x 20″ (508 mm)
- Height of side panel above baby bed: 5.75″ (145 mm)
- Microprocessor based temperature controller with Pre-warm, Manual and Skin Servo modes
- LED Display of Skin Temp.,Air Temp., Set Temp. (Resolution 0.1°C) & Heater Power %.
- LCD to display modes of operation, Alarm messages, Skin Temperature in °F and Timer.
- Thermistor based sensor with Accuracy of +/- 0.2°C (Temp. Calibration not require)
- Modes of Operation: Skin Servo, Air, Manual and Pre-Warm
- Keypad lock facility
- Skin mode: Temperature range: 34 to 38°C , Resolution : 0.1°C
- Air mode: Temperature range: Room temp. to 39°C , Resolution : 0.1°C
- Manual mode: Adjustable Heater Power 0 to 100% (with an increment of 5%), Time duration:15mins
- Pre-warm mode: To pre-warm the cradle before baby is placed on the bed. (No alarm will be activated during Prewarm mode) Adjustable Heater Power 0 to 25% (with an increment of 5%), Time duration:30mins
- Overhead heater box: Swivelling, Consists of Ceramic heater (650 Watts) placed in parabolic reflector with a safety grill & Halogen observation light (12V/50W) for observing the baby
- Operating Voltage: 220-240 VAC, 50Hz, Power: 800W (Max.)
- Alarm: Audio alarm with 10 minute mute facility & Visual alarms with message on LCD as follows
Performance/Electrical Specifications
| Alarm Condition | Alarm Messages on LCD |
|---|---|
| Skin Sensor is unplugged /Faulty | Skin Sensor Fail |
| Air Sensor is unplugged /Faulty | Air Sensor Fail |
| Measured skin temperature higher than set temperature by 1.0°C | Skin Temp. High |
| Measured skin temperature lower than set temperature by 1.0°C | Skin Temp. Low |
| Measured skin temperature higher than 38.0°C (With cut-off) | Skin Over Range |
| Measured skin temperature lower than 34.0°C | Skin Under Range |
| Measured air temperature higher than set temperature by 1.5°C | Air Temp. High |
| Measured air temperature lower than set temperature by 3.0°C | Air Temp. Low |
| Measured air temperature higher than 39.0°C (With cut-off | Air Over Range |
| Heater power is 100% for more than 15mins | Chk Sens Position |
| Heater is unplugged or faulty | Heater Open |
| Heater Power drive fail/uncontrollable | Chk. Pwr. Drive |
| Power Fail Alarm | Audio with LED indicator |
Be the first to review “Infant Radiant Warmer with Fixed Baby Cradle and Drawers with Microprocessor based temperature controller with 4 modes Skin / Air / Manual / Prewarm mode”
Related products
-
ELECTRICAL ICU BED
Frame work made of rectangular CRCA tubes mounted on 12.5cms dia swiveling castors- Two with brakerys. 18 G perforated CRCA sheet top in four sections. Electrically operated Four Separated Actuators for Maneuvering Back. Rest, Knee Rest, trendlenburg/reverse trendlenburg & height position by hand remote control system. ABS panel head and foot boards. Collapsible safety side railings. S.S. telescopic |.V. rods with four locations. Rubber buffers at four corners. Pre-treated and Epoxy Powder coated finish.
- Size : 218(L)x98(w)x55 to 80(H) cms
-
HOSPITAL SEMI FOWLER BED
Mechanically operated, two sectional, uniformly perforated CRCA sheet top bed. One fix lever handle at foot end to obtain head raise upto 80 deg. Precise rectangular tubular steel frame work. Strong re-informed, “H” Shaped legs on rubber stumps. Detachable /fix head & foot S.S. bows with laminated panels.
- Overall size : 208Lx92Wx60H
-
DELIVERY TABLE TELESCOPIC TYPE
Beb labour and delivery mainly made of mild steel. Bed top of two section, Body section mounted on rubber stumps and legs section on two castors with brake. Legs section can be completely recessed under the body section. Mattress 60 mm thick foam covered with water proof synthetic material. Table consisting of pair lithotomy poles with strip or knee pad & stainless steel bowl arrangement underneath of leg section. Finish in epoxy powder coated.
- Size body section app : 1O000(L) x 770(W) x 760(H) mm
- leg section app : 930(L) x 640(W) mm
-
BABY CRADLE
Strong tubular steel stand on rubber stumps, with handing bars mesh crib. powder coated finishing.
- Size : 103(H) x 76(L) x 42(W) cm.
Request Call Back
Reviews
There are no reviews yet.